Home / Product Range / Joints / GN 808.2
Image of Elesa product with ID 8345

GN 808.2

Universal joint shafts with friction bearing

SKU: 8345 Category:
To request 2D/3D drawings, click on the RED code/desc in Product Details below.
Technical Drawing

Product Details

Standard Elements Main dimensions Weight
Description d1 d2 H7 l1 – l d3 l3 l5 tmin. g
GN 808.2-22-K10-140-30 22 K10 140-30 22 30 48 12 310
GN 808.2-22-K10-160-40 22 K10 160-40 22 30 48 12 500
GN 808.2-22-K10-180-60 22 K10 180-60 22 30 48 12 400
GN 808.2-25-K12-180-45 25 K12 180-45 26 40 56 13 550
GN 808.2-25-K12-200-70 25 K12 200-70 26 40 56 13 620
GN 808.2-25-K12-250-105 25 K12 250-105 26 40 56 13 770
GN 808.2-28-K14-170-30 28 K14 170-30 29 40 60 13 –
GN 808.2-28-K14-200-60 28 K14 200-60 29 40 60 13 –
GN 808.2-28-K14-220-80 28 K14 220-80 29 40 60 13 –
GN 808.2-28-K14-280-140 28 K14 280-140 29 40 60 13 –
GN 808.2-32-K16-190-30 32 K16 190-30 32 40 68 16 –
GN 808.2-32-K16-240-80 32 K16 240-80 32 40 68 16 –
GN 808.2-32-K16-275-115 32 K16 275-115 32 40 68 16 –
GN 808.2-32-K16-380-210 32 K16 380-210 32 40 68 16 –
GN 808.2-36-K18-230-50 36 K18 230-50 37 40 74 17 –
GN 808.2-36-K18-270-100 36 K18 270-100 37 40 74 17 1560
GN 808.2-36-K18-290-110 36 K18 290-110 37 40 74 17 –
GN 808.2-36-K18-400-220 36 K18 400-20 37 40 74 17 2225
GN 808.2-42-K20-250-50 42 K20 250-50 42 45 82 18 –
GN 808.2-42-K25-320-120* 42 K25 320-120 42 45 108 31 –
GN 808.2-42-K25-420-220* 42 K25 420-220 42 45 108 31 –
GN 808.2-45-K22-270-50 45 K22 270-50 47 50 95 22 2520
GN 808.2-45-K22-330-100 45 K22 330-100 47 50 95 22 3010
GN 808.2-45-K22-470-240 45 K22 470-240 47 50 95 22 4140
GN 808.2-50-K25-295-50 50 K25 295-50 52 50 108 26 –
GN 808.2-50-K25-350-100 50 K25 350-10 52 50 108 26 3935
GN 808.2-50-K25-420-170 50 K25 420-170 52 50 108 26 4605
GN 808.2-58-K30-330-50 58 K30 330-50 58 60 122 29 4880
GN 808.2-58-K30-400-110 58 K30 400-110 58 60 122 29 5880

Additional information

Information

Universal joint shafts with friction bearing GN 808.2 not only join the offset between two shafts, but also enable the alignment of lengths, which depending on the overall length l1 enables the corresponding extraction length l2. The power transmission is achieved by two universal joints DIN 808 (type EG) a splined shaft and a sliding sleeve.<BR>
<BR>
It is important to check the accuracy when connec-ting the splined shaft to the sliding sleeve:
The markings -> <- have to be opposite to each other. Any kind of misconnection leads to an inhomogeneous output and to a quick abrasion.
On request

– different lengths l1 – l2<BR>
– Bores without keyway<BR>
– Bores with square<BR>
– with other or unequal bores
Specification

<STRONG>Bore code</STRONG><BR>
– Type <STRONG>K</STRONG>: with keyway<BR>
<BR>
Steel blank<BR>
<BR>
Joint bearing Areas / Pins / bearing sleeves
case hardened<BR>